Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
We have come across this great article on Tools You Need to Install a New Bathtub below on the internet and decided it made perfect sense to relate it with you on this site.
Installing a bathtub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging project. If the old tub is readily accessible, the project can move immediately; if you need to open a wall to remove the old bathtub and also place the new bath tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will require an assistant to vacate the old bathtub and embeded in the new one. See to it you have actually certified on your own for the work and fit trying it. As opposed to working with a professional to take over a halfway-completed task, it is far better to consider using one prior to you start. Possibilities are you may require an expert plumber to make tube links.
This write-up will help you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new bathtub and do not need to change the plan of your previous water pipelines.
Your devices and material list need to comprise the following:
Planning for the Installment
First of all, the supporting framework provided with the bathroom must be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps unit to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is separate the water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be rather troublesome as a result of the limited gain access to that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipes. When the supply pipelines have been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub up until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Switch on the water system as well as inspect all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub as well as also inspect the overflow electrical outlet as well as the typical outlet for leaks.
Finally, take care of the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been utilized a minimum of once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in place between the faucet and the sink. Safeguard the faucet in position with the manufacturer provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap connectors. The former kind ought to be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to break a rigid seal, triggering the water to permeate the wall between the bathroom as well as the tiling, leading to complications with wetness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and also fittings. They are sold in tubes and also cartridges, and also are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can split rather very early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our excerpt about Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to browse our posting. Sharing is caring. You never know, you may very well be doing someone a favor. Kudos for your time. Please come visit our blog back soon.
Diverse plumbing issues? We resolve. Report this page